VX 200 Mod By Augvape
1x VX200 Box Mod
1x USB Cable
1x User Manual
This product is for advanced vapers only and requires technical knowledge in order to use it. Please read the disclaimer below before purchasing this product. DO NOT purchase if you are not comfortable or experienced with these types of devices.
Note: A rebuildable coil/wick MUST be tested carefully with an ohm meter before use. If your builds are not tested prior to use, it is entirely at your own risk. Faulty wicks/coils WILL damage electronic devices. New coil/wick units must be tested and then used first on a strong basic electrical APV that has short circuit protections. No new coil/wick assembly should NOT be used on an electronic device until known it is safe to do so.
Disclaimer: Rebuildable atomizers are for advanced vapers only with access to multimeters, high discharge batteries and a working knowledge of how electronic devices work. Please ensure care is taken as to not cause damage/harm to your atomizer, vaping devices, or yourself. Upon purchasing this product you agree that Custom Vapes UK, will not be held responsible to any injuries or property damage caused by using/misusing this product.
Warranty: Low Resistance Atomizers, Clearomizers, Cartomizers, RDA, RBA may not be returned if they have been filled/built/used unless the product was defected upon receipt and we are notified within 48hrs. We strongly recommend the use of an ohm meter to check resistance for possible shorts. Due to hygiene reasons and the nature of low resistance sub ohm builds, the use of third party units/mods or non approved chargers, no returns are accepted on any atomizers and Li-Ion batteries unless the product was defective upon receipt or dead on arrival (DOA) and we are notified within 48hrs. For more information please refer to our returns policy.
Only logged in customers who have purchased this product may leave a review.
You may also like…
Introducing the next chapter in the CSMNT saga, the Layercake. This clamp style RDA only requires the tightening of a single screw to build. The icing on the cake is CERAMISTEEL, a state of the art insulation technology developed by District F5VE with a higher melting point than most metals and strength that surpasses everything else on the market, this is an RDA built to last.
• Size: 24mm
• Low Chamber
• Signature Airflow
• Squonk Ready
• Deck O-Ring
• Internal Sleeve Orings
• Matching 810 ONETips Base & Black Top
• Single Post Clamp with Ceramisteel Technology
1 x post screw
5 x O-rings
Beauty Ring: Stainless Steel, Black & Graphite.
1 x 510 contact
Colours: Stainless Steel, Black & Graphite
£ 49.99 £ 49.99
M.Terk’s highly anticipated V2 RDA is a two post rebuildable dripping atomiser that can be used in either 24 or 25mm mode by choosing the corresponding top cap.
• Black RDA with Gold Build Deck
• SS RDA with SS Build Build Deck
• 2 Post Clamp Design (Plates adjust with screws)
• Phillips Screw Heads
• Deep Juice Well
• 24mm Top Cap
• 25mm Top Cap
• Air Flow Control
• 810 Drip Tip Fitment (Goon/Kennedy fitment)
• Squonk Pin Included
Two post Axial RDA with tons of airflow options from cyclops to fully open airflow control. This RDA is sure to impress, offering phenomenal flavour and vapour packed into one package. The Axial RDA deck and deep juice well is the perfect canvas for most builds!
• 23mm Axial RDA
• 23-25mm Beauty Ring
• Airflow: Dual (holes or cyclops)
• 810 Driptip
• 810 to 510 converter
• Coils: Single or Dual
• Post Holes 4mm x 2.5mm
• Post Screws: M4
• Extra screws
• Squonk Pin
• SS Polished, Black or 24k Plated Gold