Tripod RTA By Atimizoo
1 review | Write a review
The Tripod is Atmizoo’s new approach to 22mm RTA design for single coil setups. It offers an unparalleled vaping experience focusing on performance, versatility and ergonomics. With its enhanced flavour and vapour production, potential for variable specs, instant real time access to deck, instant top refill system, easy rebuilding and attention to details, the Tripod is one step ahead of most RTAs out there.
• 22mm Outside Diameter SS316F
• Air Flow Tuning Pins: 1mm, 1.2mm, 1.5mm, 1.8mm Dia
• AFC Ring Adjusts From 0 – 4mm Dia
• 2ml Borosilicate Glass Tank. 3.4ml Extension Kit Option
• 2 Part Screw In Acetal 510 Drip Tip. Inner Diameter 4mm
• 2.5mm Pan Head Phillips Post Screws & PEEK Insulators
• Height With 510 – 39mm, Without 510 – 47mm
• Weight 56g
SS Matte is a light-brushed matte / satin finish, close to the natural appearance of CNC processed Stainless Steel.
SS Ice Matte is a medium blasted finish with special SS beams, darker (more dull) and more greyish compared to SS matte. The SS Ice Matte is a dynamic finish. It is not always the same and it gets darker over time. Also more prone to scratches compared to SS Matte.
Please Note: This atomizer has been lubricated by Atimizoo with VG due to the 37 parts it has, this avoids any potential surface rust due to any long term storage.
This product is for advanced vapers only and requires technical knowledge in order to use it. Please read the disclaimer below before purchasing this product. DO NOT purchase if you are not comfortable or experienced with these types of rebuildable atomizers.
Note: A rebuildable coil/wick MUST be tested carefully with an ohm meter before use. If your builds are not tested prior to use, it is entirely at your own risk. Faulty wicks/coils WILL damage electronic devices. New coil/wick units must be tested and then used first on a strong basic electrical APV that has short circuit protections. No new coil/wick assembly should NOT be used on an electronic device until known it is safe to do so.
Disclaimer: Rebuildable atomizers are for advanced vapers only with access to multimeters, high discharge batteries and a working knowledge of how electronic devices work. Please ensure care is taken as to not cause damage/harm to your atomizer, vaping devices, or yourself. Upon purchasing this product you agree that Custom Vapes UK, will not be held responsible to any injuries or property damage caused by using/misusing this product.
Warranty: Low Resistance Atomizers, Clearomizers, Cartomizers, RDA, RBA may not be returned if they have been filled/built/used unless the product was defected upon receipt and we are notified within 48hrs. We strongly recommend the use of an ohm meter to check resistance for possible shorts. Due to hygiene reasons and the nature of low resistance sub ohm builds, the use of third party units/mods or non approved chargers, no returns are accepted on any atomizers and Li-Ion batteries unless the product was defective upon receipt or dead on arrival (DOA) and we are notified within 48hrs. For more information please refer to our returns policy.
Only logged in customers who have purchased this product may leave a review.
You may also like…
The VapeShell is Atmizone’s RBA bridge concept for the Billet Box rev4 Boro tank and compatible tank systems. From loose lung hit to MTL, it will suit your vaping habits, with the classic air flow pins and air flow control ring included out of the box.
The optional purchase of the MTL Air Flow Pin Kit allows a true MTL experience, with extra precise adjustment using the AFC ring.
• 2mm, 2.5mm, 3mm, 3.5mm Dia Air Flow Tuning Pins~
• No Pin Air Flow Dia 4mm. Fine Adjustment With AFC Ring
• 2 x 2.5mm E-liquid Intake Holes At Base Of Deck
• 5.5mm Maximum Coil Height In Chamber
• 2.5mm Pan Head Phillips Post Screws
• SS316F & PEEK Insulators
The MTL Air Flow Pin Kit reduces the positive tube’s initial 4mm hole diameter down to 1mm, 1.2mm and 1.5mm respectively, offering the ideal air flow for a substantial range of MTL vaping profiles.
• Compatible With DotShell & VapeShell
• Laser Engraved Hole Diameter On Pins
• 1mm Hole Diameter Air Flow Tuning Pin
• 1.2mm Hole Diameter Air Flow Tuning Pin
• 1.5mm Hole Diameter Air Flow Tuning Pin