The UK's #1 Advanced Vape Store

Kryten RDA By Psyclone Mods

£ 77.99 £ 39.99

Save:48.7%
Rated 4.00 out of 5 based on 3 customer ratings
(3 customer reviews)
4 reviews  |  Write a review

Psyclone Mods release the much anticipated Kryten RDA! The legendary modder and creator of the Psyclone Hadaly RDA has created another masterpiece. The Kryten RDA was born from a labour of love in pursuit of creating the ultimate cloud atty while still being able to produce great flavour. And for squonk users a bottom feed pin is included as standard.

Product Features:
• 24mm Outer Diameter
• Dual Coil RDA
• 3 Piece Stainless Steel Construction
• Dual Adjustable Airflow
• Unique 2 Post Coil Clamping System
• Two Delrin Drip Tips – Standard & Wide Bore
• Bottom Feed/Squonk Pin Included
• PEEK Insulators
• Extra Clamp
• Extra Screws
• Extra O-Rings

Out of stock - Join the waitlist to be emailed when this product becomes available

This product is for advanced vapers only and requires technical knowledge in order to use it. Please read the disclaimer below before purchasing this product. DO NOT purchase if you are not comfortable or experienced with these types of rebuildable atomizers.

Note: A rebuildable coil/wick MUST be tested carefully with an ohm meter before use. If your builds are not tested prior to use, it is entirely at your own risk. Faulty wicks/coils WILL damage electronic devices. New coil/wick units must be tested and then used first on a strong basic electrical APV that has short circuit protections. No new coil/wick assembly should NOT be used on an electronic device until known it is safe to do so.

Disclaimer: Rebuildable atomizers are for advanced vapers only with access to multimeters, high discharge batteries and a working knowledge of how electronic devices work. Please ensure care is taken as to not cause damage/harm to your atomizer, vaping devices, or yourself. Upon purchasing this product you agree that Custom Vapes UK, will not be held responsible to any injuries or property damage caused by using/misusing this product.

Warranty: Low Resistance Atomizers, Clearomizers, Cartomizers, RDA, RBA may not be returned if they have been filled/built/used unless the product was defected upon receipt and we are notified within 48hrs. We strongly recommend the use of an ohm meter to check resistance for possible shorts. Due to hygiene reasons and the nature of low resistance sub ohm builds, the use of third party units/mods or non approved chargers, no returns are accepted on any atomizers and Li-Ion batteries unless the product was defective upon receipt or dead on arrival (DOA) and we are notified within 48hrs. For more information please refer to our returns policy.

3 reviews for Kryten RDA By Psyclone Mods

  1. Rated 5 out of 5

    Graham Carley (verified owner)

    This is my second Kryten and I love it. I never had any issues with building though I normally precut the outer legs for extra ease. I do find coil height is critical (more side than bottom / side) and a really good quality wick is needed to keep up with it. Is it better than the Goons? I think so.

  2. Rated 2 out of 5

    Jens (verified owner)

    While the machining is nice, there are a couple of things i don’t like. The Builddeck is kinda hard to build on, not impossible, but not as convenient as on a velocity style deck, the outer “postholes” for example are a little bit too low, which makes it hard to cut the wire. Then the juicewell, there are these cut outs, i guess for more room to place the coils, but as soon as i drop juice down the drip tip, it often happens that the juice seems to pur out, that happened to me with every build i tried and even with less juice, i guess i’m doing something wrong, but i don’t see what. Then there is the driptip, i don’t like that bulky one, but the smaller one won’t fit at all, i can’t get it in there, like it’s too big, i juiced it up to make the o-ring a bit smoother, i tried to “screw” it in, it won’t fit

    • Sam

      Hello Jens, I admit it can be a little tricky at first to build on the kryton but after a few tries it becomes easier. I highly recommend watching the video here https://www.youtube.com/watch?v=calQIfs4KX8. As for the leaking issue, double check that yours hasn’t been installed with the bottom feed/sqwonk pin by mistake? If it has, you can swap that out for the standard pin.

  3. Rated 5 out of 5

    Neill (verified owner)

    An absolute cloud chucker. Popped in a couple of 3mm claptons, and woosh! Bit fiddly to build. Read the Vaping Biker review for info.

Only logged in customers who have purchased this product may leave a review.

×
×
×
×

Please Note: Cookies help us deliver the best experience. By using our website, you agree to our use of them. Dismiss